STAINLESS STEEL

TIG/MIG/SAW120

Cr-Ni austenitic stainless steel filler wire with controlled ferrite content for TIG / MIG / SAW welding processes

SPECIFICATIONS

AWS / SFA 5.9 : ER 308 L

UNS NO. : S30883

TECHNICAL DATA

UTS : 52-65 kgf/mm2

YS : 38-48 kgf/mm2

ELONGATION : 35-45 %

TYPICAL APPLICATIONS

For joining and cladding AISI 304, 304L stainless steels. For welds subjected to operating temperatures from –269 to +350 O C and requiring non-scaling properties up to 800OC in air or in an oxidizing atmosphere of combustion gases. Welded joints in ferritic Cr steels (max. 18% Cr), only for root and intermediary runs if subjected to sulphurous gases. Suitable for steel grades Wnr. 1.4301, 1.4306, 1.4308, 1.4312, 1.4541, 1.4543, 1.550, 1.4552, 1.6901, 1.6902, 1.6903, 1.6905.

304L fabrication

TIG/MIG/SAW 120 H

Austenitic stainless steel filler rod/wire for welding AISI 304 with high carbon

SPECIFICATIONS

AWS / SFA 5.9 : ER 308 H

UNS No. : S30880

TECHNICAL DATA

UTS : 55-64 kgf/mm2

Elongation : 35-45%

TYPICAL APPLICATIONS

For welding of austenitic stainless steels including high carbon type AISI 304 H in industries like petrochemicals, refinery, chemical, engineering. Very good welding and flow characteristics. Storage tanks, pipe lines, pumps, valves etc.

304H pipelines

TIG/MIG 120 S

Austenitic, columbium-stabilized, stainless steel filler rod / wire for TIG/ MIG welding processes

SPECIFICATIONS

AWS / SFA 5.9 : ER 347

UNS No. : S30780

TECHNICAL DATA

UTS: 52-64 kgf/mm2

Elongation: 30.35 %

TYPICAL APPLICATIONS

For welding of 18% Cr / 8% Ni stainless steel or 18/8 SS stabilized with either columbium or Titanium. AISI 301, 302, 304, 321, 347, etc.

Stabilized SS pipelines

TIG/MIG 120 Si

Austenitic stainless steel filler rod / wire for welding AISI 304L by TIG/MIG processes

SPECIFICATIONS

AWS / SFA 5.9 : ER 308 L Si

UNS No. : S30888

SPECIFICATIONS

UTS : 55-60 kgf/mm2

YS : 28-39 kgf/mm2

ELONGATION : 35-45 %

TYPICAL APPLICATIONS

Suitable for joining stainless steels of the 18Cr/8Ni EL-type and 18Cr/8Ni/Nb type for service temperatures up to 350OC.

308L Si fabrication

TIG/MIG 120 SSi

Austenitic, columbium-stabilized, stainless steel filler rod / wire with higher silica for TIG/ MIG welding processes

SPECIFICATIONS

AWS / SFA 5.9 : ER 347 Si

UNS No. : S30788

TECHNICAL DATA

UTS : 52-64 kgf/mm

ELONGATION : 30.35 %

TYPICAL APPLICATIONS

For welding of 18% Cr / 8% Ni stainless steel or 18/8 SS stabilized with either columbium or Titanium. AISI 301, 302, 304, 321, 347, 347Si etc.

347L Si fabrication

TIG/MIG/SAW 121

Austenitic Cr-Ni-Mo stainless steel filler rod / wire for TIG / MIG / SAW welding processes

SPECIFICATIONS

AWS / SFA 5.9 : ER 316 L

UNS No. : S31683

TECHNICAL DATA

UTS : 49-60 Kgf/mm2

YS : 30-35 Kgf/mm2

TYPICAL APPLICATIONS

For chemical corrosion resistance and cryogenic steels. Suitable for steel grades Wnr. 1.4301, 1.4306, 1.4308, 1.4312, 1.4401, 1.4408, 1.4410, 1.4435, 1.4436, 1.4541, 1.4550, 1.4552, 1.4571, 1.4573, 1.4583, 1.4580 and 1.4581 as well as 1.4417, 1.6901, 1.6902, 1.6903, 1.6905. AISI 316, 316L etc. Chemical tanks, valves, pump bodies, agitator blades, impellers, pipelines etc.

316L chemical plant application

TIG 121 LF

Austenitic Cr-Ni-Mo alloyed filler rod for TIG welding of stainless steel type 316L with nil ferrite

SPECIFICATIONS

AWS / SFA : 5.9 : ER 316L-LF

UNS No. : S31683

TECHNICAL DATA

UTS: 52-61 Kgf/mm2

ELONGATION: 30-40%

TYPICAL APPLICATIONS

For welding low ferrite stainless steels of the 18 Cr / 8 Ni / Mo, type AISI 316 L, where a ferrite free weld deposit is required, i.e., fertilizer plants, chemical plants, urea application like pipelines, valves, pumps etc.

316 L nil ferrite application

TIG/MIG/SAW 121 Si

Austenitic Cr-Ni-Mo stainless steel filler rod / wire with higher silica for TIG / MIG / SAW welding processes

SPECIFICATIONS

AWS / SFA 5.9 : ER 316 L Si

UNS No. : S31688

TECHNICAL DATA

UTS: 49-60 Kgf/mm2

YS: 30-35 Kgf/mm2

ELONGATION: 30-40%

TYPICAL APPLICATIONS

For chemical corrosion resistance and cryogenic steels. Suitable for steel grades Wnr. 1.4301, 1.4306, 1.4308, 1.4312, 1.4401, 1.4408, 1.4410, 1.4435, 1.4436, 1.4541, 1.4550, 1.4552, 1.4571, 1.4573, 1.4583, 1.4580 and 1.4581 as well as 1.4417, 1.6901, 1.6902, 1.6903, 1.6905. AISI 316, 316L, 316L Si etc. Chemical tanks, valves, pump bodies, agitator blades, impellers, pipelines etc.

316 L Mo SS fabrication

TIG/MIG/SAW 122

Fully austenitic stainless steel filler rod / wire for TIG / MIG / SAW welding processes

SPECIFICATIONS

AWS / SFA 5.9 : ER 310

UNS No. : S31080

TECHNICAL DATA

UTS: 56-65 Kgf/mm2

YS: 36-47 Kgf/mm2

Elongation : 30-40%

TYPICAL APPLICATIONS

For welding corrosion and heat resisting, 25 Cr / 20 Ni steels. Very well suited for weld surfacing. Non-scaling up to 1150OC generally, up to approx. 1050O C in oxidizing and up to approx. 650OC in reducing sulphurous atmospheres. Suitable for welding steel grades Wnr. 1.2782, 1.4832, 1.4837, 1.4841, 1.4845, 1.4848, 1.4849. For welding stainless steel to carbon steel.

310 grade SS fabrication

TIG/MIG/SAW 123

Austenitic stainless steel filler rod / wire for welding dissimilar steels, AISI 309 SS by TIG/MIG/SAW processes

SPECIFICATIONS

AWS / SFA 5.9 : ER 309 L

UNS No. : S30983

TECHNICAL DATA

UTS: 52-62 Kgf/mm2

ELONGATION: 30-40%

TYPICAL APPLICATIONS

For welding 25 Cr/12Ni alloys in wrought or cast forms. Welding of 18 Cr / 8 Ni base metals when severe corrosion conditions exist. Also used in welding dissimilar metals, such as joining 18 / 8 to manganese steel. Applying sheet lining of 12 percent chromium steels to mild steel shells.

309 SS grade fabrication

TIG/MIG 123 LMo

Austenitic stainless steel filler rod / wire for welding dissimilar steels and buffer layers

SPECIFICATIONS

AWS / SFA 5.9 : ER309LMo

UNS No. : S30986

DIN 8556 : SG X8 Cr Ni Mo 2313 (1.4459)

TECHNICAL DATA

UTS: 52-65 Kgf/mm2

ELONGATION: 30-40%

TYPICAL APPLICATIONS

Used for joining dissimilar steels with stainless steel of any type. Used as a buffer layer prior to surfacing with 316 L for corrosion resistant overlays. Higher tolerance to dilution than 309S92 increase range of applications, but note that the lower ferrite potential reduces tolerance to dilution compared with related electrodes.

Used for dissimilar welds where lower ferrite value and higher ductility is required. Not recommended for structural applications where post weld heat treatment is to be carried out or for long term high temperature service above 400OC.

316 L buffer welding alloy

TIG/MIG/123 Si

Austenitic stainless steel filler rod / wire with higher silica for welding dissimilar steels, AISI 309 SS by TIG/MIG/SAW processes

SPECIFICATIONS

AWS / SFA 5.9 :ER 309 L Si

UNS No. : S30988

TECHNICAL DATA

UTS: 52-62 Kgf/mm2

ELONGATION: 30-40%

TYPICAL APPLICATIONS

For welding 25 Cr/12Ni alloys in wrought or cast forms. Welding of AISI 309 L Si, 18 Cr / 8 Ni base metals when severe corrosion conditions exist. Also used in welding dissimilar metals, such as joining 18 / 8 to manganese steel. Applying sheet lining of 12 percent chromium steels to mild steel shells.

309 SS grade fabrication

TIG/MIG 124

Fully austenitic stainless steel filler rod / wire for joining ER 385 type of stainless steels

SPECIFICATIONS

AWS / SFA 5.9 : ER 385

UNS No.: N08904

TECHNICAL DATA

UTS: 52-62 Kgf/mm2

ELONGATION: 30-40%

TYPICAL APPLICATIONS

For welding of Er385, HV-9 A and HV-9 stainless steels and similar alloys for excellent resistance to various corrosive media and temperature. Used in pharmaceuticals, fertilizer & chemical industry components.

Er385 stainless steel

TIG/MIG 125

Duplex stainless rod / wire for welding 2209 type duplex stainless steels

SPECIFICATIONS

AWS A 5.9 : ER2209

UNS No. : S39209

TYPICAL APPLICATIONS

Used for pipework and general fabrication in offshore oil, gas & chemical process industries. Suitable for standard duplex stainless steels UNS S31803 (wrought) J92205 (cast), BS 318S13. Proprietary alloys such as Hy-Resist 22/5 (Avesta Sheffield), SAF 2205 (Sandvik), AF22 (Mannesmann), Uranus 45N (Creusot) can be welded using TIG/MIG 125.

Welding duplex Stainless steel

TIG/MIG 126

Austenitic stainless steel filler rod / wire for welding AISI 317 L base metals

SPECIFICATIONS

AWS / SFA 5.9 : ER317L

UNS No. : S31783

TECHNICAL DATA

UTS: 55-65 Kgf/mm2

ELONGATION: 30-40%

TYPICAL APPLICATIONS

This molybdenum bearing type ER 317 L grade is suitable for welding ER 317 L type of stainless steels. Welding of AISI 317 L type, for severe corrosion applications involving sulphuric and sulphurous acids and their salts, for steel fabrications in which post-heat treatment is to be avoided, for joining stainless steel to low alloy and carbon steels.

Welding of 317 L

TIG/MIG 127

TIG/MIG filler rod / wire for welding 13% Cr stainless steels

SPECIFICATIONS

AWS / SFA 5.9 : ER 410

UNS No. : S41080

TECHNICAL DATA

UTS: 52-63 Kgf/mm2

ELONGATION: 20%

TYPICAL APPLICATIONS

Stainless steel filler alloy for TIG/MIG welding of 13% Cr steels. Used for joining as well as hard-facing applications made of AISI 410 metal like turbine blades, guide vanes, pelton wheels etc.

Welding for straight chrome steel

TIG/MIG 128

Ferritic stainless steel filler rod / wire for welding AISI 430 type base metal

SPECIFICATIONS

AWS / SFA 5.9 : ER 430

UNS No. : S43080

TECHNICAL DATA

UTS: 45-68 Kgf/mm2

YS: 30-36 Kgf/mm2

ELONGATION: 20-30%

TYPICAL APPLICATIONS

Welding of corrosion and heat resisting steel grades. Weld surfacing on sealing surfaces of gas, water and steam fittings operating at temperatures up to 450OC. Non-scaling up to 900OC in air and in an atmosphere of oxidizing or sulphurous combustion gases. Especially suitable for building up edges. Good resistance to attack by sea water, organic and inorganic acids (nitric acid, sulphuric acid).

Welding of 430 grade SS

TIG/MIG 130

Austeno-ferritic Cr-Ni-Mn steel filler rod for TIG welding all types of steels

SPECIFICATIONS

AWS/SFA-5.9 : ER 312

UNS no. : S31380

TECHNICAL DATA

UTS: 66-73 Kgf/mm2

YS: 48-52 Kgf/mm2

ELONGATION: 22-24%

TYPICAL APPLICATIONS

Used for joining, medium, high carbon, low alloy & high alloy steels, tool steels, spring steels, manganese steels, case-hardening steels, quenched steels, steel castings, die steels etc.

Welding of all grades of steel

TIG / MIG 133

Austenitic stainless steel filler rod / wire for joining manganese steels and stainless steels type AISI 307

SPECIFICATIONS

AWS / SFA 5.9 : ER 307

UNS No. : S30780

TECHNICAL DATA

UTS: 56-65 Kgf/mm2

0.2% PROOF OF STRESS: 40-52 Kgf/mm2

ELONGATION: 30-45%

TYPICAL APPLICATIONS

Used for joining dissimilar steels, armour plates, manganese steels and generally difficult to weld steels. Buttering before hard facing. Gives strong, ductile and tough austenitic deposit which work hardens from 12 - 32 RC. Can be used for mix welding where deposits have to be heated. The most versatile for dissimilar steels.

Welding of Mn steel

TIG/MIG 133 Si

Austenitic stainless steel filler rod / wire with higher silica for joining manganese steels & stainless steels type AISI 307, 307 Si

SPECIFICATIONS

DIN : SG-X 15 Cr Ni Mn 18.8 (1.4370)

TECHNICAL DATA

UTS: 65-74 Kgf/mm2

YS: 37-49 Kgf/mm2

ELONGATION: 30-38%

TYPICAL APPLICATIONS

Used for joining dissimilar steels, armour plates, manganese steels and generally difficult to weld steels. Buttering before hard facing. Gives strong, ductile and tough austenitic deposit which work hardens from 12 - 32 RC. Can be used for mix welding where deposits have to be heated. The most versatile for dissimilar steels.

Welding of 307 Si steel

TIG / MIG 134

Austenitic stainless steel rods and wires for TIG/MIG welding

SPECIFICATIONS

AWS / SFA 5.9 : ER 320 LR

UNS No. : N08022

TECHNICAL DATA

UTS: 52-60 Kgf/mm2

 

ELONGATION(L=4D) : 30-40%

TYPICAL APPLICATIONS

Welding of austenitic stainless steels, corrosion resistance parts like pipe lines, pump impellers, agitators, vacuum rotors, heat exchanger headers etc.

Heat exchanger headers
Ador Fontech Logo

CONTACT US

ADOR FONTECH LIMITED

Belview, 7 Haudin Road, Bangalore-560042

Tel: 080 25596045/73

Fax: 080 25597085

E-mail: customerservice@adorfon.com

Submitting Form...

The server encountered an error.

Form received.

Ador Fontech Limited © 2017 Privacy Policy

Ador Fontech Limited

Belview, 7 Haudin Road, Bangalore-560042

Tel: 080 25596045/73 Fax: 080 25597085

Fax: 080 25597085

E-mail: customerservice@adorfon.com

CONTACT US

ADOR FONTECH LIMITED

Belview, 7 Haudin Road, Bangalore-560042

Tel: 080 25596045/73

Fax: 080 25597085